T
his feature allows you to edit or skip channels from the channel
list that have bad or weak signals or channels you do not want to
watch.
1
Press the MENU/SELECT button. The on-screen menu
appears. Then press the CURSOR RING DOWN repeatedly
until INSTALL is highlighted. Press the CURSOR RING
right to enter the INSTALL submenu.
2
Press the CURSOR RING DOWN repeatedly until
CHANNEL EDIT is highlighted. Then press the CURSOR
RING RIGHT or LEFT to access the CHANNEL EDIT list.
3
Press the CURSOR RING UP or DOWN to scroll
through the list of channels. Or press the NUMBER buttons
on your remote control to select a specific channel.
4
With the channel you want to edit selected, press the
CURSOR RING RIGHT to mark the channel as
SKIPPED. (Channels you mark SKIPPED will not appear
when you use the CH[annel] +/– buttons to change channels
while watching TV.)
When you want to add a channel that has been marked
SKIPPED, press the CURSOR RING UP or DOWN to high-
light the channel. Then press the CURSOR RING RIGHT to
remove the word SKIPPED.
5
Press the STATUS/EXIT button to exit the menu.
SETTING TIME AUTOMATICALLY
The steps in this section tell you how to set AutoChron™ to
download the time from your PBS station to your TV. After suc-
cessful setup, AutoChron™ will automatically maintain the cor-
rect time using your PBS station until you set the time manually.
1
Press the MENU/SELECT button. The on-screen menu
appears. Then press the CURSOR RING DOWN repeatedly
until INSTALL is highlighted.
2
Press the CURSOR RING RIGHT to enter the INSTALL
submenu. Then press the CURSOR RING DOWN repeated-
ly until AutoChron is highlighted.
3
Press the CURSOR RING RIGHT to enter the
AutoChron SET TIME area.
4
Press the CURSOR RING RIGHT again to select AUTO.
Within a few seconds, a menu containing the time-zone
options appears.
5
If necessary, press the CURSOR RING UP or DOWN to
highlight your correct time zone. Then press the CURSOR
RING RIGHT. Within a few seconds, the option of Daylight
Savings Time appears on screen.
6
If the Daylight Savings Time option you want to select is
not highlighted, press the CURSOR RING UP or DOWN
to highlight the option. Then press the CURSOR RING
RIGHT to activate your selection.
7
Press the number buttons on your remote to enter the
channel number for your PBS station (02, 15, or 121, for
example). Wait until the TV completes its search. If the time
was not found, you will need to locate the correct channel
number for your PBS station and input that number.
8
Press the STATUS/EXIT button to exit the menu.
5
U
SING THE
INSTALLATION
FEATURES
AutoChron™
CHANNEL
EDIT
The message shown to
the right indicates that
AutoChron™ is not
finding a PBS station at
the channel you input.
Check the channel
number for your PBS
station.You will need to
input the correct num-
ber for the time to be
found.
Channels that Auto
Program (see page 5)
determined not to contain
active broadcast signals are
marked SKIPPED.
HELPFUL HINT
A
utoChron™ gives you the option of setting the time manually or
automatically.
T
he AUTO PROGRAM feature will scan for channels with
active broadcast signals and store those channels in the TV’s
memory. It will tune up to 69 channels for antenna, and up to 125
channels for cable. After you run AUTO PROGRAM, you can use
the CH(annel) +/– buttons to quickly and easily select stations.
You can also press the PROG. LIST (Program List) button on your
remote to see a list of the channels.
1
Press the MENU/SELECT button. The on-screen menu
appears. Then press the CURSOR RING DOWN repeated-
ly until INSTALL is highlighted.
2
Press the CURSOR RING RIGHT to enter the INSTALL
submenu. Then press the CURSOR RING DOWN repeated-
ly until AUTO PROGRAM is highlighted.
3
Press the CURSOR RING RIGHT to begin the automatic
search for channels. The progress of autoprogramming is
displayed.
4
When the programming is done, press the STATUS EXIT
button to exit the menu.
Kommentare zu diesen Handbüchern