Philips DP 6000 Bedienungsanleitung PDF herunterladen

Philips

Communication &

Security Systems

INSTALLATION INSTRUCTIONS

1 GENERAL INFORMATION

For a detailed description of DP 6000 paging calls refer to

Installation Instruction No. 63 for the High Performance Control

Desk (LBB 5800).

1.1 Description

Philips Personal Security System PS 6000 combines paging functions

with portable alarm facilities for people on the move in hazardous

environments or are liable to incur some personal risk. The system

is based upon Personal Security Transceivers (PST), a High

Performance Desk and a Field Control Panel (FCP). The system

incorporates security facilities such as manual alarm and automatic

system scanning. In addition, a detector circuit is built into the

transceiver which will initiate an alarm procedure when no

movement of the transceiver is detected.

Communication between the PST and the FCP is always via the

LBB 5800 Desk. Each FCP monitors the status of its own PSTs

programmed into the system. An FCP can be programmed to

monitor the PST’s fully automatically without any action by the

operator or PST holder, and also by manual confirmation of the PST

holder.

1.2 System size

Each Field Control Panel can cater for up to 16 PSTs and the PSTs

are programmed to react to their dedicated call buttons and LEDs

on that particular panel. Up to 31 FCPs can be interconnected via

the desk.

A High Performance Desk LBB 5800 can supply enough power to

support only one FCP. If more than one FCP is used in the system,

they must be powered via an external supply unit.

The RS 422 communication bus can be used to connect all the FCPs

together, in parallel, to the LBB 5800 Desk (see page 15 for system

set up).

1.3 System Scanning

The FCP can be programmed to scan the PST’s in the system at

preprogrammed intervals and check the status of each. An

automatic or an additional manual response from the PST to this

check call can be programmed, for each individual channel, into the

FCP. In the former instance, the PST will automatically send the

status information back to the FCP without disturbing the PST

holder, whereas in the latter, the PST holder must, within a

predetermined time, acknowledge that a call has been received by

pressing the Alarm Reset Button on the PST.

When the auto-scan facility is programmed and set for user

enable/inhibit, the auto-scan facility will be activated by pressing the

channel Auto-Scan key on the FCP, pressing Auto-Scan key again

this will disable the auto-scan activity and so on.

1.4 Field Alarm Calls

The FCP can be programmed to react to an Alarm Call from the

PST in several ways; When the Alarm LED lights, a Direct Call can

be transmitted to establish contact with the PST holder. This call

will be initiated by using the Direct Call Key for that channel. If no

action is taken by the operator within a predetermined time, a

preprogrammed alarm call can be automatically routed to another

PST. A built in delay timer can activate one to three relay outputs in

the FCP, which can be used to activate some other device e.g.

telephone exchange. The relay function can be programmed for

continuously ON or pulsed ON.

2 PROGRAMMING THE FCP

2.1 General

All programming of the FCP must be carried out via the LBB 5800

desk. The FCP must first be set “present” by the allocation of a

dedicated address and all the various functions required by the

customer must be done by further software programming. Only

one uninitialised FCP may be connected to the RS 422 line at any

given time.

When an uninitialised FCP is powered up, the top row of LEDs will

all blink slowly. When initialised, the FCP address LED will be

illuminated during power up. These are represented by the top two

rows of LEDs (1 - 31) reading from top left to bottom right. The

power LED in the top left corner will be illuminated. (Powering up

the desk with an FCP connected takes max. 60 sec.)

2.2 Editor

The Editor function of the desk is the means by which the system

variables are programmed into the FCP.

When the Editor is opened, the program variables can be entered

via the keyboard and the desk bleeper gives an audible indication of

correct or incorrect entries.

The normal sequence of programming the FCP is to first enter the

required MENU followed by the menu COMMAND DIGIT,

followed by the PROGRAM VARIABLE(S).

INSTALLATION

INSTRUCTIONS

DP 6000 DIGITAL PAGING SYSTEM

December 1997 Page 1 of 15

FIELD CONTROL PANEL LBB 6005

1 2 3 4 5 6 ... 14 15

Inhaltsverzeichnis

Seite 1 - FIELD CONTROL PANEL LBB 6005

PhilipsCommunication &Security SystemsINSTALLATION INSTRUCTIONS1 GENERAL INFORMATIONFor a detailed description of DP 6000 paging calls refer toIns

Seite 2 - 2.5 Bleep Tones

9. WIRING DETAILSX1 - 9-pin D-type socket for connection to the High Performancedesk (LBB 5800)Pin No. Function1 +12 V power supply from the desk(fuse

Seite 3

PS 6000 and DP 6000 SYSTEM WIRINGInstallation details of the various units in the PS 6000 system can be found in the relevant Installation Instruction

Seite 4 - 4.1 Address Allocation

DP 6000 DIGITAL PAGING SYSTEM INSTALLATION INSTRUCTION 69December 1997 Page 12/15EnterLightMenuRecallAlarmPEnterLightMenuRecallAlarmPEnterLightMenuRe

Seite 5

INSTALLATION INSTRUCTION 69DP 6000 DIGITAL PAGING SYSTEM Page 13/15 December 1997TABLE 1FCP DEFAULT VALUESFUNCTION DEFAULT VALUEFCP Address (not inial

Seite 6 - 5.7 ALARM CALL REPEAT TIME

DP 6000 DIGITAL PAGING SYSTEM INSTALLATION INSTRUCTION 69December 1997 Page 14/15TABLE 3The codinf value transmitted by the PST during any kind of a

Seite 7

INSTALLATION INSTRUCTION 69DP 6000 DIGITAL PAGING SYSTEM Page 15/15 December 19971235467891015 1413121116Key to symbols1. Handset (LBB 5804 optional)

Seite 8

During programming, the desk display will show the programinformation as it is entered.Use the DIRECT CALL key of the desk to select the correct FCP

Seite 9

3 FCP PROGRAMMING3.1 PS 6000 menu selectionTo enter the PS 6000 menu, OPEN THE DESK EDITOR, SELECT and PRESS key “A”as shown in para. 2.3 and obse

Seite 10 - FCP Rear view

COMMMAND “3” - ALLOCATE ADDRESS DISPLAY SHOWS “GIVADR (1/0)”Keystroke “1” - Will give the connected uninitialised FCP the lowest free (unallocated) a

Seite 11 - INSTALLATION INSTRUCTION 69

4.3 Address Status Changing within Command “4” (STA FCP NR.) Submenu:The following gives the correct key selections necessary to move from one status

Seite 12 - December 1997 Page 12/15

5.3 EDITING THE ALARM CALL STRINGThe display will show “FCP Nr., Channel Nr., “a” and the call string (e.g. 0105a - - - - - - - - - -).The alarm call

Seite 13 - Table 2

5.8 MANUAL ACKNOWLEDGE TIMEThe display will show “FCP Nr. and Channel Nr. followed by “ack. time” followed by the programmed time (e.g. 0105 ACK TIME

Seite 14

The display will now show “Sel. Chan. Nr”, select the channel to be edited (01 - 16) and the display will show the programmed auto scanstatus of the

Seite 15

8.1 FUNCTION ASSIGNMENTThe display will now show the current setting of the FCP e.g.Function position - 1 2 3 4 5 6 7 8 9Displa

Kommentare zu diesen Handbüchern

Keine Kommentare

Philips DP 6000 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Nein Philips DP 6000 herunter. Philips DP 6000 User's Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Philips DP 6000