Philips AZ3830/12 Bedienungsanleitung PDF herunterladen (Seite 4)

Remote control

Important!

• Before using the remote control, remove

the insulation plastic tab as shown

in figure @.

• If the remote control does not function

correctly or the operating range is

reduced, replace the battery with a new

(CR2025) type battery.

1 Pull the battery tray out as shown

in figure @.

2 Replace a new battery according to polarity

indication, and fully insert the battery tray

back to the original position.

• Incorrect use of batteries can cause

electrolyte leakage and will corrode the com-

partment or cause the batteries to burst:

• Do not mix battery types: e.g. alkaline with

carbon zinc. Only use batteries of the same

type for the set.

• When inserting new batteries, do not try to

mix old batteries with the new ones.

• Remove the batteries if the set is not to be

used for a long time.

Batteries contain chemical substances, so

they should be disposed of properly.

Using AC power

1 Check if the power/mains voltage, as shown

on the type plate located on the

bottom of the set, corresponds to your

local power supply. If it does not, consult your

dealer or service center.

2 Connect the power cord to the

AC~ MAINS inlet and the wall socket.The

set is now ready for use.

3 To switch the set off completely, withdraw the

power cord from the wall socket.

4 Install the unit near the AC outlet and where

the AC power plug can be easily reached.

• Disconnect the power cord from the wall

socket to protect your set during heavy thun-

derstorms. Children could seriously injure

themselves as the free end of the cable may

still be live if only the connector is removed

from the MAINS socket at the back of the

unit.

The type plate is located on the

bottom of the set.

Auto power saving

• When the source selector is adjusted to

CD/USB and the set is in the PAUSE

position for 5

minutes, the set will be auto

switched to the stop position to save power.

• When the source selector is adjusted to

CD/USB and the set is in the STOP position

for 15

minutes, the set will auto switch off.

Helpful hints:

–To avoid unnecessary energy consumption,

always press POWER on the set to power

off the set after using the set.

CAUTION

- Visible and invisible laser radiation.

If the cover is open, do not look at

the beam.

- High voltage! Do not open.You run

the risk of getting an electric shock.

The machine does not contain any

user-serviceable parts.

- Modification of the product could

result in hazardous radiation of

EMC or other unsafe operation.

This set complies with the radio

interference requirements of the

European Union.

Power Supply

Basic functions

Switching on/off the set

1 To switch on, press POWER.

➜ Display lights up.The system will switch to

the last selected source.

2 To switch off, press POWER again.

➜ Display lights off.

Adjusting volume and sound

Adjust the sound with the VOLUME and

DBB controls.

Digital tuner

Tuning to radio stations

1 Press repeatedly SOURCE (or TUNER

on the remote control) to select FM or

MW.

➜ “TUNER” is displayed briefly, then the

radio station frequency, waveband and, if

programmed, a preset number are shown

(See 2).

2 Press and hold ∞ or § until the frequency in

the display starts running.

➜ The radio automatically tunes to a station

of sufficient reception. Display shows

“

SEARCH” during automatic tuning.

3 Repeat step 2 if necessary until you find the

desired station.

•To tune to a weak station, press ∞ or §

briefly and repeatedly until you have found

optimal reception.

To improve radio reception:

• For FM, extend, incline and turn the tele-

scopic aerial. Reduce its length if the signal is

too strong.

• For MW, the set uses a built-in aerial. Direct

this aerial by turning the whole set.

Programming radio stations

You can store 15 FM and 10 MW radio

stations in the memory manually or

automatically (Auto store).

Manual programming

1 Tune to your desired station (see Tuning to

radio stations).

2 Press PROG to activate programming.

➜ Display: PROG flashes.

3 Press ALBUM/PRESET +/- (

ALBUM/PRESET

3, 4

on the remote

control ) once or more to allocate a number

(FM: from 1 to 15; MW: from 1 to 10).

4 Press PROG to confirm.

5 Repeat steps 1-4 to store other stations.

Helpful hints:

–You can erase a preset station by storing

another frequency in its place.

Autostore

Autostore automatically starts programming

radio stations from preset 1. Any previous

presets e.g. manually programmed will be

erased.

1 Press repeatedly SOURCE (or TUNER

on the remote control) to select FM or

MW.

2 Press PROG until “AUTO” flashes.

➜ Available stations are programmed (MW

or FM). After all stations are stored, the

first autostore preset station will then

automatically play.

To listen to a preset or autostore

station

Press the ALBUM/PRESET +/- (

ALBUM/PRESET

3, 4

on the remote

control ) buttons once or more until the

desired preset station is displayed.

Basic Function/ Radio MP3-CD/ CD Player

ifu_az3830_euro_eng 2006.8.22 11:33 AM Page 4

1 2 3 4 5 6 7 8 9

Kommentare zu diesen Handbüchern

Keine Kommentare

Philips AZ3830/12 Bedienungsanleitung Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für CD Spieler Philips AZ3830/12